Retroreflectors against ARS

When Author was a graduate student his graduate advisor had a single-cell oversized gold plated retroreflector in remote sensing LIDAR lab.  Author heard rumors that it was the same type of retroreflector as that originally placed on the surface of the moon to measure the distance to the Loonar surface from Earth using a laser. This reflector was composed of squares with a side of about 10 to 15cm (~ 4 to 6 inches) to the best of Author's memory.  Someone from a private company jokingly asked once if he (the graduate advisor) had to travel to the moon to get that reflector.

A perfect retroreflector will reflect all radiation that falls onto it to its origin.

A similar rough inexpensive simple single cell retroreflector can be made from aluminum foil, cardboard, and the painter's or other tape as shown in Fig. 1.  Fig. 2 shows the back side of the reflector, and Fig. 3 illustrates the 4 equal size squares covered with aluminum foil on one side which are stacked together to form the reflector shown in Fig. 1 and 2.  Writer suggests such retroreflectors may be used to reflect the microwave (and possibly some other types of unidentified ARS) radiation roughly back to its origin.  Since some of the ARS phenomena appear to be relying on electromagnetic radiation some of that radiation should be reflected back by such single cell retroreflector to a location in proximity of its origin.  The imperfection of the reflector can be thought of as an advantage for anti-ARS use since there is a certain uncertainty as far as where exactly the reflected radiation will land at introducing an unpredictability factor for the ARS personnel to be mindful of.  Multiple single cell retroreflectors may be placed at multiple locations at an ARS-contaminated site or stacked together to span a wider surface area.

Note:  Rretroreflectors are essential components of any sleeping station and any ARS contaminated site.  Careful retroreflectors locations selection is required because it is the ARS personnel who is in the possession of the active EMF equipment which they can regulate the intensity and direction of.  If one elects to use such reflectors it is recommended to make a large number of them (i.e. tens or hundreds) to cover a significant relevant area to make sure the ARS personnel is not under the illusion that nothing they send out is ever going to return back to them.

Retroreflector tests performed at the primary research site in Hampton, VA 23666

The main retroreflector test performed at the primary research site in Hampton, VA 23666 before it shut down on August 28, 2025 was a test involving a relocation of a single retroreflector shown in Fig. 1 to spots in the proximity of the Affected Person at the Hampton, VA 23666 research site. This was done by placing the reflector on top of a floor (pole) lamp (typically referred to as "Torchiere Pole Light") disconnected from the power supply and with the lightbulb removed.  The "Torchiere Pole Light" with the reflector on top of directed upwards (as shown in Fig. 4) was moved together with the Affected Person.  One of the tests also involved placing the retroreflector on top of the Pavilion Sleeping Station (PSS) as shown in Fig. 4.  The single retro-relfector tests only lasted a couple of days (only one reflector was in use).

After the "Torchiere Pole Light" retroreflector test the Affected Person went to sleep in the PSS and started experiencing a strong skin burning sensation.  At the time of the test one side (the entrance side) was convered with steel roof panels with no aluminum foil layer (all other sides were covered with aluminum and steel roof panels).  An emergency covering of the entrance side with aluminum foil was carried out which removed the skin burning sensation while in the sleeping station.  Since steel is only good for EMF shielding at lower frequencies (see STEEAL) Writer interprets this result as an indication that the ARS techniques must include the use of microwave radiation of higher frequencies such as i.e. in the cell phone and WiFi or other bands for EMF harassment, through the wall remote sensing and other adverse residential purposes.

About the MASER

The first LASER was in the microwave region and as such was called a MASER.  Even though a lot of times the microwaves are induced using an antenna it should also be possible to create a MASER with specific desired frequencies such as those corresponding to the WiFi and cell phone frequencies (i.e. WiFi MASER).  Due to the high intensity and collimation of the beam it should not produce much interference for surrounding WiFi signals in residential settings and could be used for a variety of applications where propagation into tight confined spaces is necessary with or without data transfer.  Although Writer is not an expert on MASERs and microwave radiation.  It should also be remembered that a lot of building materials used in the United States let microwave radiation through.

An ARSMASER

 An ARSMASER is a collective term introduced to refer to any type of a directed energy device (i.e. microwave or any other type, presumably capable of passing through many common building materials) which could directly deposit or be used as an assistive tool in the process of depositing the ARS Matter (ARSM) into the human body.

The Affected Person would occasionally feel "spot treatment" of different body regions as if they were irradiated with a beam of unknown radiation causing some unpleasant feeling at the spot and some weakness.  Writer suspects that the use of ARSMASER may include (among other techniques) a more conventional process of light/microwave photo activation of an active ARS-derivative substance inside of the body after inhalation or intake through food to form ARSM at chosen regions inside of the body after photo-activation.

A song called "Press the button" by a band called "Technology" with the chorus saying: "Press the button. .... And your dream will come true.  Press the button.  Why aren't you happy?  There is no longer anything left to pursue..."